Justice
Dangerous Idiot
https://www.tlc-direct.co.uk/Produc...MIq53Pg4W97wIVDbbtCh1MgQUtEAQYASABEgJuTPD_BwE
I use these little chaps
Got something to say or just want fewer pesky ads? Join us... 😊
[Help] Advice from an electrician please
- Thread starter Rugrat
- Start date
I use these little chaps
dejavuatbtn
Well-known member
What’s the sauce?
Billy the Fish
Technocrat
There's a brown wire, a blue wire and a yellow/green wire. Make sure you twist them all together so it's left nice and tidy for the next person.
I had to replace the light in my sons room and discovered WAGO fittings.
It was like discovering the meaning of life. They are amazing.
Baldseagull
Well-known member
If you only have 2 wires at the switch, on one cable, they are live and switched live, the black or blue wire you have there will not be connected to neutral.
The red or brown wire will be a live feed from your lighting circuit, the black or blue will connect back at a rose or junction box to the live (red or brown) that you see at the light fitting, it would be best if you could disconnect at the rose or junction box, as you can disconnect the neutral there too, and the live feed to the switch. Failing that I would disconnect the switched live only (black or blue) at the switch and put it into a wago. leave the live feed in the switch terminal or put it in a wago, safer than leaving it taped up and floating.
I am not an electrician either, but I don't think you have had clear advice from the one person that has replied and I believe is an electrician.
Last edited:
I don't recommend battering your eyelids without consulting a professional.
maresfield seagull
Well-known member
- May 23, 2006
- 2,317
- Thread starter
- #28
No, only 2 wires out, both black too!
maresfield seagull
Well-known member
- May 23, 2006
- 2,317
The load side ( light fitting )neutral in the switch you disconnected, was it in a connector block
Or was the switch double pole and you had four cores connected to it 2 in 2 out ?
maresfield seagull
Well-known member
- May 23, 2006
- 2,317
Your theory is normally correct But you are making assumptions We need more info
- Thread starter
- #32
maresfield seagull
Well-known member
- May 23, 2006
- 2,317
Sorry I meant by switch
It'should either be a normal 6@ light switch 2 cores in switch &neutral in a connector Or a double pole switch where all the cables are terminated into the switch
Obviously you have disconnected them already
Before some comedian makes a joke
- Thread starter
- #34
Here's a pic - the two brown wires went to the switch. No idea what the others do but the switch sits alongside a double socket so assume that's the power in ... wires at top will be off to light
maresfield seagull
Well-known member
- May 23, 2006
- 2,317
OK in this instance Bald Seagulls is kind of on the right track
Now from the pic I can see the neutral is unbroken
So that needs separating ,take it out of the wago looking connector ( the blue to the light fitting you removed )
leaving the blue feed in the connector
Then ideally fit either a connector block( and tape ) or wago on the brown that didn’t go to the light fitting
That’s your live supply
It’s quite possible dependent on the cable route ,? once this done the cable to the old light may pull out
Turn your entire Fuse board off Just to be safe whilst doing this
IF you don’t know which cable is the feed and which went to the light ?
Then split blues and browns and put connector block s on each core
Then put the switch or blanking plate back on
Can you put up a pic of the switch ?
Are the green / yellows connected into a little brass pillar with a screw on top Can’t make it out in the pic
Last edited: